Tutorials

  • Design & CAD ×
  • Kinematics ×
  • CATIA ×
  • NX Unigraphics ×

TURBOFAN

Avnish Kumar (अवनीश कुमार )
in Modeling
16 1 Expert
The Rolls-Royce Trent 900 is a high bypass turbofan produced by Rolls-Royce plc to power the Airbus A380, competing with the Engine Alliance GP7000. https://www.youtube.com/watch?v=T0K7wmLCEhw&list=PLbzPiq3XQNA0NSQ4YxUyulhkGAQiaRbz4&ab_channel=CADCAMSOFTINFO Initially proposed for the Boeing 747-500/600X in July 1996, this first application was later abandoned but it was offered for the A3XX, launched as the A380 in December 2000. Despite the RB211 success, the large civil turbofan market was dominated by General Electric and Pratt & Whitney, and Rolls-Royce share was only 8% when it was privatised in April 1987. Advanced Low-Pressure System
CATIA how turbofan catia

how can create admin mode of catia ?

özgür kesebir
in Design & CAD
15 7 Intermediate
Here is the tutorial to run catia as admin.
CATIA

How to create a turbofan exhaust mixer in CATIA V5

Chris Shakal
in Design & CAD
15 1 Beginner
Steps below:
CATIA engine v5 catia exhaust jet mixer turbofan

Car design in NX

MANIKANTHA P
in Modeling
16 0 Beginner
Car design
NX Unigraphics automobile design car

NX 11:Creating Assembly

Anand Panchal
in Assemblies
14 2 Beginner
A tutorial on Sub assembly and showing arrangements of hydraulic cylinder-piston assembly.
NX Unigraphics sub-assembly cylinder hydraulic arrangements assembly unigraphics nx

Mold Design in NX 10

gcom
in Design & CAD
14 3 Intermediate
Mold Design in NX 10. Without Mold Wizard and fully parametric.
NX Unigraphics tutorial 10 nx

Mold Wizard Siemens NX CAD Tutorial

Shuvam Kumar
in Modeling
14 0 Intermediate
How To Use Mold Wizard in Siemens NX CAD
NX Unigraphics cad extraction cavity core tutorial 12 wizard nx design mold

Designing an UMBRELLA using CATIA (Surface modelling)

Jasper Aaron
in Modeling
14 0 Beginner
hey guys.. in this tutorial.. you get to know how to model an UMBRELLA in simple steps.
CATIA sweep tutorials basic umbrella modelling surface tutorial catia

Clamp Design

Anup Chauhan
in Drafting
14 1 Beginner
Clamp Design https://www.instagram.com/p/CqAkr5bKxDZ/
NX Unigraphics assembly modeling drafting drawing clamp siemens nx nx nx cad

How to model airplane in catia?

Rahul
in Design & CAD
14 0 Intermediate
To proceed First have a blueprint of your desired aircraft.
CATIA catia

how to do analysis of gear in Ansys 11?

harikrushna dodiya
in Design & CAD
13 2 Intermediate
do as following step
CATIA 11 ansys catia

Sheet Metal Rolling Machine

akash kumar
in Modeling
13 1 Expert
FOR knowledge'Basic knowledge is lower to a higher position
CATIA ansys solidwork catia

CATIA Car body Imagine and Shape design with blue print - Tutorial for beginners

THE CAD SPIDER
in Modeling
14 0 Beginner
This video contains Step by step procedure to create a Car Body Concept Design in CATIA using Imagine and shape design.
CATIA catia tutorials catia surface modeling catia imagine and shape design catia car body design catia

DRONE DESIGN in SIEMENS NX

MANIKANTHA P
in Modeling
13 0 Beginner
An unmanned aerial vehicle (UAV) (or uncrewed aerial vehicle,[2] commonly known as a drone) is an aircraft without a human pilot on board. UAVs are a component of an unmanned aircraft system (UAS); which include a UAV, a ground-based controller, and a system of communications between the two.[3] The flight of UAVs may operate with various degrees of autonomy: either under remote control by a human operator or autonomously by onboard computers[4] referred to as an autopilot.
NX Unigraphics siemens nx unigraphics drone

Basic Modelling 1 (NX Unigraphics)

Bhargava Krishna Marripati
in Modeling
13 0 Beginner
Basic modelling techniques using NX Unigraphics.
NX Unigraphics modelling nx
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.