Tutorials

  • Design & CAD ×
  • Composites ×

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

Constantin STANCESCU
in Design & CAD
73 18 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw
Autodesk Inventor centrifugal_pump inventor_2014 ipt multi-body spiral coil

More Keyshot and Photoshop Tips

FredSWUG
in Modeling
34 14 Intermediate
I don’t think of myself as an expert in Keyshot or Photoshop, but I can often get some decent results from both programs. My biggest hurdle sometimes is simply remembering the process I typically use. This article is being created as a tutorial for you, and a reference for me if I forget a step. I have another tutorial on Keyshot you may also enjoy: https://grabcad.com/tutorials/some-keyshot-tips
KeyShot tricks tips rendering render photoshop keyshot

New approach in designing and modelling an Oil pump using Inventor 2016

Ebrahim Abu Has
in Design & CAD
107 13 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...
Autodesk Inventor ticks tips some splines parallel shafts keyways keys shaft design gears spur

Convert STL (or OBJ) Mesh to SOLIDWORKS Model (NURBS)

FredSWUG
in Modeling
67 12 Intermediate
Need to convert an STL (or OBJ) file into a "real CAD model"? There are several tutorials which already exists for this topic. I'm making a new tutorial to give additional information.
SOLIDWORKS part convert model sldprt mesh stl

Bell design drawing

Mohsen Jahanbakhsh
in Modeling
11 12 Intermediate
Bell design drawing
SOLIDWORKS designing modeling inventor catai solidworks

Cap screws and machine screws

dea
in Drafting
65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

How to convert SLDPRT file to STEP file

Hajiba bakhti
in Design & CAD
14 11 Intermediate
To convert a part, we have 2 steps.
SOLIDWORKS sldprt iges step convert

test

kemal dursun
in Drafting
0 11 Intermediate
test
ArchiCAD test

SURFACE MODELLING IN CATIA

Jasper Aaron
in Modeling
25 11 Intermediate
CATIA is a software known for surface modelling, here is a small car done using wireframe and surface in CATIA
CATIA rendering redering body car modelling surface catia

(VIDEO TUTORIAL)تمارين سوليدو{​كس (Solidworks Exercises in arabic)

Ali Nasser
in Modeling
18 10 Intermediate
اكثر من 20 تمرين بأستخدام سوليدوركس Solidworks Exercises تمارين سوليدوركس تدريب سوليدوركس تدريبات سوليدوركس SOLIDWORKS exercise سوليدوركس pdf Model mania
SOLIDWORKS 2001 2000 mania model pdf exercise exercises solidworks

Introduction to Blow Mold design in SW

Edgar Gidoni
in Modeling
24 10 Intermediate
This is an introduction to blow mold design using SolidWorks. The recommended workflow to successfully accomplish the design and modeling of a fundamental production tool in today's industry.
SOLIDWORKS tecnicursos molds plastic swblowmolds blowmolds swtutorials swhowto

Mountain Bike Design

MANIKANTHA P
in Assemblies
30 10 Intermediate
Mountain Bike Design part 01 using unigraphics
NX Unigraphics assembly unigraphics bike mountain mtb

SolidWorks Tutorial: Path Mate Animation with Spring Movement

Usman Akhtar
in Assemblies
10 9 Intermediate
files download link is in the description of video in YouTube for your practice. In this SolidWorks Assemblies Tutorial you will learn how to arrange a path mate, we also do a simple and basic animation of whole design.
SOLIDWORKS mate path tutorial assembly practice files solidworks

(VIDEO TUTORIAL) Solidworks Tutorial #155 How to Design a JET GAS TURBINE Assembly (Engine) in Solidworks Easy Design

Praveen Kumar
in Assemblies
46 9 Intermediate
Full Assembly Jet Gas Turbine Engine . Part Two Available on our YouTube Channel................. I hope you like this Tutorials This Tutorial Made by Request for Collage Students I'm always upload easy way drawing not hard. And unique trick friends. So please Subscribe & Share every Friends.
SOLIDWORKS mechanical engineering rendering modeling design assembly solidworks
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.