Tutorials

  • Design & CAD ×
  • Autodesk 123D ×
  • OBJ ×
  • GrabCAD Print ×
  • GrabCAD Workbench ×
  • 3D Manufacturing Format ×

How to FDM Print for Part Sliding Clearance

GrabCAD Tutorials
in Assemblies
13 4 Intermediate
If you are 3D printing parts that have to fit/slide together after printing, you will need to put some sort of clearance between those parts in your CAD system. A good starting place is a clearance 2x the layer height you are going to print at, but you should make a few smaller test prints at different clearances to see if the 2x layer height rule holds for your particular situation and orientation. Have fun and happy printing!
GrabCAD Print sliding clearance printing 3d fdm

How do i track changes by others?

Sara Sigel
in Design & CAD
5 1 Intermediate
Your partner can upload a new version, leave a sketch, or write a comment to let you know about a change. If you have notifications setup, then you'll get an email when any of these happen. https://grabcad.com/email/edit You can also compare changes between versions, which is very useful. For a visual comparison of what is different from one version to the next, see the steps, below.
GrabCAD Workbench file grabcad cad workbench management version revision

how to draw campbell diagram in ansys pls hlp me

harikrushna dodiya
in Design & CAD
3 0 Intermediate
campbell diagram step start from 9 plz see step 9
GrabCAD Workbench

How can I change picture order after uploading a model ?

shubham gupta
in Design & CAD
2 3 Intermediate
Please go through this tutorial.
GrabCAD Workbench order image gif

Stacking Your Parts in Z for FDM

Stratasys
in Assemblies
2 0 Intermediate
Have long thin flat parts you’ve always wanted to print right on top of each other in FDM but the slicer never allowed you to? Learn how to use this exclusive new feature in GrabCAD Print Pro!
GrabCAD Print fdm stacking stratasys 3d printing software grabcad print pro

3D Modeling of a Braitenberg Vehicle in 4 Steps using Autodesk 123D Design

Yoana Ivanova
in Modeling
2 0 Intermediate
This tutorial is suitable for designers who have a basic knowledge of using the open source product Autodesk 123D Design. The steps to build a Breitenberg vehicle are as follows: 1. Modeling a wheel: a cylinder with a diameter of 2 cm and a height of 0.5 cm is placed in the workspace. Drill a hole in it by drawing a circle with a diameter of 0.3 cm and extruding - 0.5 cm with the Extrude tool. We soften the edges of the cylinder with Fillet Radius: 0.5. 2. Clone the wheel: rotate the resulting wheel 90° along the Z axis and copy it with Ctrl+C and Ctrl+V. 3. Modeling the vehicle body: regarding the design of the vehicle body, there are various options. In this case the author models a classic vehicle, which is most often shown in the bibliographic sources. After drawing and extruding a surface with the desired shape we apply Fillet with radius 35 on the back edge and with 30 on the front edge for a contemporary design (i could provide more images if it is needed). On the selected side edges we successively apply Fillet with a radius of 9. 4. Make a special place for the sensor: it is necessary to select the square plane that is located in the middle of the case and successively apply Sketch > Project, Sketch > Offset and Construct > Extrude with a negative value.
Autodesk 123D breitenberg vehicle

how do I choose a picture (rendering) that will appear first in the library?

Inspire
in Design & CAD
1 0 Intermediate
1yshetynrw7uywru yuuywrywr
GrabCAD Workbench

how to draw campbell diagram in ansys pls hlp me

harikrushna dodiya
in Design & CAD
1 0 Intermediate
in modal analysis go to analysis setting than go rotodynamic check coriollis effect on than do campbell diagram on feed your data and solve it
GrabCAD Workbench

JP_005_GrabCAD Print: 部品摺動部の隙間をＦＤＭ造形する方法

Stratasys Japan
in Assemblies
0 0 Intermediate
造形後にはめ合わせるまたは摺動（スライド）させる必要がある部品を3D造形する場合、CADシステムで該当する部品の間にある程度の隙間を設ける必要があります。目安として、造形する際の積層ピッチの2倍の隙間から始めるとよいでしょう。ただし、小さいサイズで何度かテスト造形を行い、積層ピッチの2倍の法則が特定の状況や向きに当てはまるかを確認することをお勧めします。それでは3Dプリンタで楽しくモノづくりをしていきましょう！
GrabCAD Print fdm 3d printing clearance sliding

How can I create a new Autodesk Fusion 360 project in GrabCAD Workbench?

Sara Sigel
in Design & CAD
0 1 Intermediate
Here is a quick video tutorial to create a model using the GrabCAD Workbench and Autodesk Fusion 360 integration.
GrabCAD Workbench grabcad new create workbench fusion360
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.