Tutorials

  • Design & CAD ×
  • Autodesk 123D ×
  • IronCAD ×
  • Kompas-3D ×
  • Lagoa ×

Параметризация модели через переменные в "Компас-3D"

Egor Chugay
in Modeling
13 0 Intermediate
Tutorial relevant for users "Kompas-3D". I don't know if they "Kompas-3D" is used in other countries, but I know "Kompas-3D" most popular in Russia, so further explanation will be in Russian. If you need English version, please comment tutorial, and I make translate. В данной заметке рассмотрено построение параметрической модели на примере корпуса микросхем типа QFP, модель строится в САПР «Компас-3D». Представленный ниже способ - лишь один из многих возможных. И я искренне надеюсь, что кому-то он поможет лучше разобраться 3D моделированием, а кто-то увидит, как оптимизировать процесс. Несмотря на то, что построение модели выполнялось в «Компас-3D», подобные механизмы могут присутствовать и в иных системах, так что возможно пригодится пользователям другого ПО. Описанный ниже способ предполагает наличие определенного навыка работы с 3D моделями, и не содержит подробного описания последовательностей нажатия клавиш, скорее описана методика построения и взаимосвязь объектов.
Kompas-3D qfp tutorial parametric kompas-3d

IronCAD - Top 10 Tips

Nick
in Modeling
3 5 Expert
Ten top tips for IronCAD
IronCAD hints tips ironcad

IronCAD - Using the Co-ordinate system to create a section

Nick
in Modeling
2 0 Intermediate
Use the Co-Ordinate systems to create a section plane. This is a handy alternative the section tool, as it does not cut the solid model.
IronCAD section cross

3D Modeling of a Braitenberg Vehicle in 4 Steps using Autodesk 123D Design

Yoana Ivanova
in Modeling
2 0 Intermediate
This tutorial is suitable for designers who have a basic knowledge of using the open source product Autodesk 123D Design. The steps to build a Breitenberg vehicle are as follows: 1. Modeling a wheel: a cylinder with a diameter of 2 cm and a height of 0.5 cm is placed in the workspace. Drill a hole in it by drawing a circle with a diameter of 0.3 cm and extruding - 0.5 cm with the Extrude tool. We soften the edges of the cylinder with Fillet Radius: 0.5. 2. Clone the wheel: rotate the resulting wheel 90° along the Z axis and copy it with Ctrl+C and Ctrl+V. 3. Modeling the vehicle body: regarding the design of the vehicle body, there are various options. In this case the author models a classic vehicle, which is most often shown in the bibliographic sources. After drawing and extruding a surface with the desired shape we apply Fillet with radius 35 on the back edge and with 30 on the front edge for a contemporary design (i could provide more images if it is needed). On the selected side edges we successively apply Fillet with a radius of 9. 4. Make a special place for the sensor: it is necessary to select the square plane that is located in the middle of the case and successively apply Sketch > Project, Sketch > Offset and Construct > Extrude with a negative value.
Autodesk 123D breitenberg vehicle

How to create a perforated sheet metal

Bob Heijningen
in Design & CAD
1 1 Intermediate
could be that you want to use rectangular patern. by creating one hole and copying it over the surface of the sheet. i actually never use sheet metal parts but here it goes.
IronCAD perforations

IRONCAD Training 01-04 | Drag & Drop Modeling

Emil.Rindell
in Modeling
1 0 Beginner
Four videos that describes the Drag & Drop Modeling basics in IRONCAD.
IronCAD training triball easy cad user friendly beginner 3d cad ironcad

IronCAD - Linked Cross Sections

Nick
in Modeling
0 0 Intermediate
Create independent parts all driven by the one linked cross section
IronCAD section cross linked ironcad structural

IronCAD - Multifeature part from one Cross Section

Nick
in Modeling
0 0 Intermediate
Create a pipe section with flanges at each end, using one circle to drive the bore diameter with flange OD offset from this.
IronCAD mechanical section cross pipe ironcad

Tutorial: How to create a helix along a 3D curve

Yaroslav
in Design & CAD
0 0 Beginner
Look the video. Important moments: - The orientation of cross section - Twist profile angle must be more then 360 Angel: 360*15 = 5400, Where 15 - number of coils Result file: http://grabcad.com/library/tutorial-how-to-create-a-helix-along-a-3d-curve-1
IronCAD 3d ironcad curve helix cord tipsntricks
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.