Tutorials

  • FEM ×
  • Kinematics ×
  • Process ×

How to Raise Your GrabCAD Score

FredSWUG
in Process
80 33 Beginner
Your score on GrabCAD is not terribly important, but it is nice to have a better score, and not be "ranked" dead last on a site with four million users. What can you do to increase your score?
points ranking score grabcad

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to Prepare Your 3D Model for Manufacture

Russell Everard
in Process
32 1 Expert
Using this ladies bike model found in the thousands of models available on GrabCAD I have made a step-by-step guide on how to break down your top level assembly for the workshop or for outsourcing.
SOLIDWORKS cutting laser fabrication cnc fixings assemblies manufacture solidworks

Introduction to Finite Element Method /CAE

Prasertsak Naksakul
in FEM
16 0 Beginner
Finite Element Method for product design and process improvement.
fluid improvement process cae analysis stress design fem

How to Convert 2D Images into 3D STL Files

GrabCAD Tutorials
in Process
14 0 Beginner
There are several ways to create 3D models from BMP images. This tutorial explains how to do this by converting a BMP file to an STL file. The following content was taken from Stratasys' Resources Center
modeling 3d 2d software bmp stl

Spring stiffness calculation in SOLIDWORKS

Ahmed Sakib
in FEM
14 1 Intermediate
How to calculate spring stiffness with Solidworks simulation @cadingal . Static structural analysis of a helicoil spring will be done using self contact approach to calculate spring stiffness in Solidworks.
finite element analysis fem solidworks spring stiffness calculation spring stiffness simulation

Linear Static Study in 10 simple steps.

Ilirjan Leci
in FEM
14 0 Intermediate
Linear Static Study with SolidEdge.
fea solidedge

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

How to Create the Perfect GrabCAD Tutorial

Sylvia Daly
in Process
13 0 Beginner
GrabCAD Tutorials have some exciting new features I want to make sure you're aware of. I'll also recap a few overall best practices for creating and publishing a Tutorial so you get the most out of sharing your Tutorial.
tutorials grabcad

Car crash test and Study motion with Solidworks.

CAD Zest
in Kinematics
10 1 Beginner
There is broken bridge and road so that I had to jump the car from the edge of bridge. There is some calculations like what is speed of car and what is the gap between both the roads.
analysis crash car study motion solidworks

How to do Structural Analysis of a Car Wheel in SOLIDWORKS?

Ahmed Sakib
in FEM
10 0 Intermediate
How to do Structural Analysis of a Car Wheel in SOLIDWORKS? @cadingal Learn..... How to assign gravity load? How to assign Force load? How to evaluate stress, deformation & factor of safety?
car wheel analysis fea car wheel solidworks simulations car wheel simulation car wheel fea

Simulation of Two Flanges with Bolts

zaher
in FEM
10 10 Intermediate
Solidworks Simulation, Bolt connection
solidworks flanges bolt_connection simulatiom

External Windmill flow simulation in solidworks fully explained for beginners from scratch

Amit Mourya
in FEM
10 0 Intermediate
In this video you are going to learn how to do external flow simulation in solidworks. i have defined and make everything from scratch like making geometry explaining why i am doing a particular step etc. i have also explained how to define boundry conditions in solidworks . what is mean by reference of axis . how to do wind flow simulation in solidworks with deep explaination i hope this video helps you a lot . I also define how to use equation goal . if you want to learn about more flow simulation in solidworks checkout this playlist https://www.youtube.com/playlist?list=PLjExndY7KnkBnQ6LS2u9ZfjOMOVGFIfxI and if possible support us on paypal so that we can create more and better content : paypal.me/nobodyknow137
turbine wind conditions boundary aerodynamic graph plot how tutorial solidworks simulation flow external

Linking ABAQUS and FORTRAN

Rahul
in FEM
9 6 Beginner
ABAQUS and FORTRAN are linked to execute User Subroutines such as VUMAT, UMAT, USDFLD, etc. You can find various versions of ABAQUS and FORTRAN Available. Here is the compatibility list: ABAQUS 2017 - Intel Composer XE 2013 or above, - Visual Studio 2010 or above v6.14 - Intel Visual Fortran 12.0 or above - Visual Studio 2010 or above One can download Student version of FORTRAN for free from here: https://software.intel.com/en-us/qualify-for-free-software/student
vumat fortran abaqus

Simple motion study with SolidWorks

Jack K
in Kinematics
9 1 Beginner
This tutorial introduces a quick and easy way to do a motion study. It just takes a few minutes to draw a stick diagram and add a few dimensions and mates, and then animate the diagram to show how the parts move and interact with each other. (Of course we could make an assembly of fully detailed parts for a motion study, but that takes more time and more work) I first learned this technique with CATIA sketches, and it's just as useful with SolidWorks.
simulation animation study motion
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.