Tutorials

New approach in designing and modelling an Oil pump using Inventor 2016

107 13 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

73 18 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw

LEGO - 01 Basic Dimensions & Bricks Explained

68 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.

Cap screws and machine screws

64 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.

How do I scale a model in Inventor?

50 13 Beginner
:)

LEGO - 02 Building Bricks with Parameters

37 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.

Tutorial: How to make energy chain and animate that by parameter

35 4 Beginner
Step by step

[VIDEO] Bending Plate Animation Inventor 2020 Tutorial

33 1 Intermediate
This tutorial will show how to create a bending process of a plate in animation, hope this video will give you clear explanation. please leave comment below

How to model a Control lever shaft using Inventor 2014?

31 8 Intermediate
If you are really interested in modeling with Inventor (2014), try to apply every step with respect to their order and watch how you reach the model. You can watch the live modeling of this part with Inventor 2021 by using this link: https://youtu.be/gOkTy_oJdH0 Enjoy!

Modelling of Impeller

28 4 Beginner
Modelling of Impeller

How to model a curved spring

27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA

Basic Tutorial for AutoCAD

28 3 Intermediate
This Tutorial will give you idea about basic introduction about AutoCAD, user guide tutorial for tools, best practices, applications. This tutorial is the web series for basic AutoCAD so follow up for the next file. Hit like if it is useful.

Inventor 2019 Crash Course for Complete Beginner

26 6 Beginner
Still spending so much time, struggling with learning Inventor on your own? You can stop now! Get a detailed explanation of every single tool. This is the first of a series, and I'll like you to check below to know what to expect in this volume. In this Tutorial, I shall introduce briefly the Inventor 2019 interface, demonstrate how to access the inventor self-help learners path, demonstrate the way to set up the software with your desired Unit style, and then put in my best to handle every single sketch tool in detail.

Construction of a Dodecahedron

22 4 Intermediate
Some CAD software such as AutoCAD does not have all the geometric objects, in particular the famous Dodecahedron. A method simple drawdown in descriptive geometry.

How to draw tangent arcs between two circles in AutoCAD?

22 4 Beginner
In this tutorial I am going to show you the easiest way to draw arc between two circles when you need specific radius.