Learn about the GrabCAD Platform
Get to know GrabCAD as an open software platform for Additive Manufacturing
Visit our new homepage
Home
Control
Shop
Streamline Pro
Partner Program
Print
Community
Log in
Library
Challenges
Groups
Questions
Tutorials
Engineers
Blog
Log in
Gregory Williamson
Follow
6
followers
United States
Models
About
Models
48
Tutorials
0
More
Followers
6
Following
0
Likes
0
Following
0
Followers
6
Likes
0
Models
Sort by:
Recent
Recent
Popular
Most liked
Most commented
Most downloaded
Oasis Park Entrance Sign
Cute simple entrance sign for my park
0
9
0
Modern Bench
Nice minimalist bench
0
11
0
Water Fountain
A basic water fountain. Does not meet ADA regulations
0
9
0
Traffic Control System Assembly
I started by drawing the roads in a "+" shape, and then extruded it. After that I drew a square around the intersection and then extruded it, creat...
1
88
2
F360 Updated Saw Assembly
I started by
0
3
0
Scandinavian Furnishings Assembly
A section view was applied in these pictures. The full assembly contains a grass roof, this is a reference to the prehistoric tradition of growing ...
9
219
0
Bed Frame
I started by sketching the side profile and extruding it. I then made the legs by sketching an area to remove using extrude cut. I then sketched an...
3
147
0
Vanity
I started by making a rectangular prism, and then adding the legs. To make the drawers, I made a sketch on the front to make the layout of where th...
2
77
0
Side Table
I started by drawing four circles on the top plane. I then extruded them up to create the legs of the table. I then made two top planes, both above...
1
47
0
Bookshelf
I started this part by sketching the side profile and extruding it. I then added the different appearances and was finished.
3
46
0
Chair
I made the metal part by drawing the shape on the side profile and extruding it. After that I drew a square on the front profile and extrude cut it...
4
298
0
Pendant Light
I started this part by sketching the rectangle and extruding it up. I then offset the bottom of the rectangle and extrude cut into the body. I then...
2
29
0
Ottoman
I started by drawing the four legs on the top plane. I then extruded them and set a draft. I then added a reference plane to make the pieces connec...
2
19
0
Rocking Chair
I started by drawing the side profile of the chair. I then extruded it out to make the physical part. I then made sketches to draw the areas i woul...
4
62
0
Fixture Block
I started by sketching the side profile and extruding it by 100. I then extruded the cylinder by 5 mm on each side. I then made the cut in the midd...
1
30
0
Wheel Linkage Assembly
I started by using the concentric mate to get the rod onto the wheel, then used another concentric mate to get the smaller rods circle to line up w...
0
222
0
Trailer/Food truck Assembly
I started by getting all of the parts into an assembly file. I then used several mates to get the wooden floor onto the top of the trailer frame. I...
0
36
0
Radial Swing Block
I started by drawing the side view and dimensioning everything. The most difficult part for me was spacing the diamond shape in the middle, 9.5mm a...
0
41
0
Fork Spacer
Fork Spacer 1 Mass = 8514.45 grams Volume = 1850966.90 cubic millimeters Surface area = 132762.67 square millimeters I drew the side view by start...
0
19
0
Tapered Pin Slot
Mass : Mass = 859.40 grams I started by drawing the side view and extruding it by 100. I then extruded the 20x15 rectangle out both sides by 10, a...
0
20
0
Gripper Assembly
Center of mass: (millimeters) X = -87.94 Y = -0.27 Z = 0.02 I used concentric and coincident mates to get both of the arms connected to the bas...
0
47
0
Scissor Lift Assembly
Center of mass: (millimeters) X = 415.42 Y = 90.39 Z = -21.04 I used a coincident and concentric mate to get the linking cylinder onto the base....
1
28
0
Connecting Rod Assembly
I started by connecting the 2 wheel components to the base using concentric and colinear mates. I then used the concentric mate to get the connecti...
0
15
0
Tooling Cylinder
(Mass and other info at bottom) Tooling Cylinder 1 I started by drawing the top half of the front profile and revolved it. I then drew the 2, 12 m...
0
15
0
1
2
