Learn about the GrabCAD Platform
Get to know GrabCAD as an open software platform for Additive Manufacturing
Visit our new homepage
Home
Control
Shop
Streamline Pro
Partner Program
Print
Community
Log in
Library
Challenges
Groups
Questions
Tutorials
Engineers
Blog
Log in
James Matthew
Follow
33
followers
Sheffield, Vermont, United States
Models
About
Models
31
Tutorials
0
More
Followers
33
Following
0
Likes
1222
Following
0
Followers
33
Likes
1222
Models
Sort by:
Recent
Recent
Popular
Most liked
Most commented
Most downloaded
Homemade segway
Self-balancing two-wheeled vehicle. The electronic components were downloaded from GrabCAD - it was a long time ago, but I think the models were c...
15
159
1
Bicycle Phone Holder
This is designed to fit on the top tube of a bicycle to hold a smart phone. It is modeled to fit the 33mm top tube on my bike and will hold a phon...
4
76
0
Drink/plate Holder for Crutch
For the crutch accessory challenge. It will hold cups, cans, or bottles up to 8 cm diameter and plates up to 22 cm. (I don't know if it will hold...
11
75
4
Egg Drop (try and fail)
This attempt at dropping an egg was a dismal failure. I decided to post it anyway. I think that the "watch spring" method has some merit - it all...
11
33
6
Pressure Switch
This switch is 16 x 16 x 7 mm excluding the tube connection. It could be modified for vacuum by placing the tube connection on the opposite surfac...
22
113
5
Request: Vacuum elbow fitting
Fulfilling a request. No guarantee on dimensions. Is sized for 1/8" ID tubing - if the thread on the fitting is 1/4"-28, the tubing cannot be muc...
22
178
5
Tahe Kayak Seat 2
For the Tahe challenge. Width adjustment my not go to the full 620, but is close.
16
40
3
Tahe Kayak Seat
Entry for the GrabCAD Challenge
17
53
2
Oxygen Splitter / Flow Control
Another variation on the splitter. Assumes a tubing ID of 5 mm, OD of 8 mm. Volume is approximately 47 cc. Height is just under 10 cm.
11
47
1
Exterior Stairs
Exterior stairs and wall
3
43
2
Oxygen Splitter/Flow Control
The splitter requires 4 printed components - possibly 6 because the wheel probably cannot be made as is without support material. Each cross sec...
13
53
0
Sense Level Gauge 2
Intended operation: the center shaft has helical grooves in it. As the float moves, the tabs in the float's center hole cause the shaft to turn th...
10
63
1
Sense Level Gauge
This is intended to mount on top of the fluid tank. The sensor is protected from the fluid with a flexible, petroleum-safe "boot" that moves with ...
8
153
2
Extension ladder
Two-piece aluminum extension ladder, two 4.25 meter sections. Created with FreeCAD 0.16.
39
1999
3
Request: Shear piston shaft seal
Requested shaft seal
12
264
0
Request: Shear cylinder o-ring
Requested O-ring
8
117
1
Spherical Shelf Unit
Inspired by the spherical bookshelves done a while ago by Liam Biggs.
23
267
5
Kitchen Faucet
A faucet for a kitchen sink
20
941
6
Street Lamp
Lamp model was done in FreeCAD; rendering done with BricsCAD Platinum
13
229
3
Kayak
More FreeCAD practice
33
793
3
Request: 120mm fan grill
Fan guard in FreeCAD format as requested (and for FreeCAD practice)
38
1839
7
Wagon Wheel
Practice with FreeCAD
11
234
0
Request: Texas a&m
For the request of a Texas A&M logo. It's in DXF and DWG.
6
162
1
Travel Cup
I started this for the recent bottle challenge but couldn't think of anything unique. So, now it's just a cup.
5
121
0
1
2
