Tutorials

  • Modeling ×
  • Drafting ×
  • Assemblies ×
  • Autodesk Inventor ×
  • Text file ×

Cap screws and machine screws

dea
in Drafting
65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

LEGO - 01 Basic Dimensions & Bricks Explained

dk
in Modeling
68 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.
Autodesk Inventor bricks dimensions lego

How to model a curved spring

Jens Nielsen
in Modeling
27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA
Autodesk Inventor coil 3dintersection surface sweep spring

How to model a dodecahedron

Jens Nielsen
in Modeling
15 8 Intermediate
Let me show you how to model a platonic surface body and use it for a weldment structure. 3D-file at: https://grabcad.com/library/dodecahedron-32
Autodesk Inventor 3dsketch polygon

[VIDEO]Universal Joint

Dono Cre'
in Modeling
14 6 Beginner
Universal Joint design which consists of several design parts such as; Main Shaft, Connector shaft, Spider, Bearing. In making this design using several features, among others: ~ 2D Sketch ~ Extrude ~ Circular Pattern ~ Fillet/Chamfer ~ Assembly Feature ~ Shell ~ etc.
Autodesk Inventor assembly automotive tutorial design inventor autodesk joint universal

Inventor 2019 Crash Course for Complete Beginner

CAD Pond
in Modeling
26 6 Beginner
Still spending so much time, struggling with learning Inventor on your own? You can stop now! Get a detailed explanation of every single tool. This is the first of a series, and I'll like you to check below to know what to expect in this volume. In this Tutorial, I shall introduce briefly the Inventor 2019 interface, demonstrate how to access the inventor self-help learners path, demonstrate the way to set up the software with your desired Unit style, and then put in my best to handle every single sketch tool in detail.
Autodesk Inventor beginner sketch tutorial 2019 inventor autodesk

Robust Master Parts

ROTHMECH
in Modeling
1 6 Intermediate
Make robust designs using multi-body master parts.
Autodesk Inventor part master body multi

Vee block/v block inventor

Alejandra Cervantes Tetrika México
in Modeling
7 5 Beginner
https://youtu.be/ovJpfP6kAv8
Autodesk Inventor inventor beginner ver block

How to create a Square to Round (Autodesk Inventor)

David Tate
in Modeling
21 5 Beginner
This tutorial will run you through the process to create a sheet metal square to round from start to finish. Including flat pattern.
Autodesk Inventor lengthy inventor round square metal sheet

How to design a M10 Hex Nut using Autodesk Inventor 2020

Farhan Shajahan
in Modeling
1 5 Beginner
In this tutorial i will be showing how to create a M10 Hex Nut using Autodesk Inventor 2020.Normally people create a polygon followed by extruding it and later creating a hole of 10 mm to design one, but that is not enough.We need to do the following steps of creating a polygon, extruding it, create a taper of 45 degree on the top and bottom surface followed by creating a hole and later threading it. Another issue noticed in Autodesk Inventor 2020 is that the thread created on the surface is not the real thread and is just a texture map.Hence we will show you on how to create an actual thread.
Autodesk Inventor industrial manufacture manufacturing m10 hex nut

LEGO - 02 Building Bricks with Parameters

dk
in Modeling
37 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.
Autodesk Inventor parameters lego

How to model a truncated icosahedron with Autodesk Inventor

Jens Nielsen
in Modeling
12 4 Intermediate
Mix 2D- and 3D sketches to create this platonic body.
Autodesk Inventor

Autodesk Inventor easy practice sketch execution

bartos tihamer
in Modeling
0 3 Beginner
How create drills, create mirror sketch and different extrudes and holes....
Autodesk Inventor practice drills cad sketch inventor

Inventor 2021 | Radial Engine | Assembly 9

CAD Pond
in Assemblies
11 3 Beginner
In this video, I demonstrated the assembly of the cylinders and pistons with the crank case used in a typical radial engine. Video demonstrations to the parts used, can be found on my youtube channel linked in my profile. Happy Modeling!
Autodesk Inventor airbus inventor engine radial aviation boeing airforce aircraft

woodwork for inventor and freeform skeleton tutorial

Lauri Link
in Modeling
17 3 Beginner
How to model freeform skeleton body to generate sun chair ribs
Autodesk Inventor skeleton woodwork chair freeform
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.