Tutorials

  • Drafting ×
  • Engineering Fundamentals ×
  • Theory ×
  • Autodesk Inventor ×
  • Delmia ×
  • Fusion 360 ×
  • PTC Creo Parametric ×

Cap screws and machine screws

dea
in Drafting
65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

Project Manager

3D Machine and Technologies by Ferhat
in Drafting
13 0 Expert
Hello, I have been working professionally on technical drawing and design since 1993 I have worked on a wide variety of projects. I am a freelancer Nice to talk and learn with everyone. f.sogukkuyu@gmail.com
Autodesk Inventor

Gear "Module" Explained in 1 Minute

Engineering Juice
in Engineering Fundamentals
7 2 Beginner
#GearModule #Gears #Module https://amzn.to/3fjbhH3 Module=d/N (d is pitch diameter and N is number of teeth) Number of Teeth = Reference Diameter/ Module Reference Diameter = Module x Number of Teeth Reference Pitch = Module x Pi Like and subscribe for more!
Fusion 360 definition formula module calculation reduction explained ratio gear

#11 Creo Sketch Tutorial- Inspect Tools In Creo

MD DESIGN ACADEMY
in Drafting
3 0 Intermediate
Friends! Don't forget, if you like our videos please "Subscribe", "Like", "Favorite" and "Share" it to your friends to show your support.
PTC Creo Parametric tutorial parametric creo ptc

[EPS 04] Cara membuat Etiket Gambar Teknik | Autodesk Inventor

Suryo Puji Buwono
in Drafting
3 0 Beginner
Cara membuat Etiket Gambar Teknik dengan Autodeks Inventor
Autodesk Inventor teknik gambar e-tiket

How to Create Full Unfold Cross Section

Vladimir Palffy
in Drafting
2 0 Beginner
In this video, you can see the logic or explanation - How Xsec Full(Aligned) and Full(Unfold) works - you need to select Axis for this type of section or not.
PTC Creo Parametric section cross

How to display different assembly positions on a drawing

Vladimir Palffy
in Drafting
2 0 Beginner
Do you have a mechanism and you need to show 2 and more positions on the drawing?
PTC Creo Parametric mechanism positions assembly

Isometric view drawing with Dimensions in fusion 360

vikram ahuja
in Drafting
2 0 Beginner
Hi Guys, In this video, I am going to tell you that how can you make a Isometric view drawing with Dimensions in fusion 360. I have taught you how to make Isometric view drawing with Dimensions, which will make you understand in simple way. If you want to learn Fusion 360 software and If you want more tutorials, Then you can also subscribe my Youtube Channel, Whose link I have given you below. My Youtube Channel Name is: Ahuja Technical Hant https://www.youtube.com/channel/UClh7lX8d70gIwoA7z5Tt2Yg https://youtu.be/tEDOTYTzFgs
Fusion 360 draftingwithdimentions cadmodeling fusion360 drafting

CAD I CAM I CAE I BIM Tutorial

Tashamjar Guruji
in Drafting
2 1 Beginner
Welcome to SS e Academy.com Now Tutorial Creo Parametric 5.0 You have more learn CAD I CAM I CAE I BIM Software Tutorial In www.SSeAcademy.com
PTC Creo Parametric creo revit autocad cae cam cad

Create blue print by Autodesk Inventor

Ebrahim Zokaee
in Drafting
2 1 Intermediate
In this tutorial, study how to create a blue print by Autodesk inventor.
Autodesk Inventor inventor drafting blue print

onvert 3D model into 2D Fully Dimesioned Drawing using Drawing Workspace of Autodesk Fusion 360.

Harsh Priyanshu
in Drafting
2 0 Beginner
Learn how to Convert 3D model into 2D Fully Dimesioned Drawing using using Drawing Workspace Autodesk Fusion 360 . this video is totally meant for beginners so i overlooked few tools and things which are not necessary for now:) I hope you enjoyed the designing process and the model. if you enjoyed the process and model, then hit subscribe and like the video. and don't forget to comment your views on this model and process.
Fusion 360 autodesk drawing 360 fusion

How to create cross sections

Vladimir Palffy
in Drafting
1 0 Beginner
In this tutorial, you can learn How to create cross sections - full and local
PTC Creo Parametric tutorial creo sections cross

Having the problem when show annotation model used in the drawing

Mohit Saxena
in Drafting
1 0 Beginner
"Having the problem when show annotation model used in the drawing"
PTC Creo Parametric
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.