Tutorials

  • Modeling ×
  • Process ×
  • Autodesk Inventor ×
  • FreeCAD ×
  • Fusion 360 ×
  • solidThinking Evolve ×
  • Solid Edge ×

How to design Complete Drone Overview

Rugved Chavan
in Modeling
83 7 Intermediate
Complete Drone design with 1. raspberry pi 4 extension 2. pixhawk 3. landing gears 4. drone frame 5. telemetry module 6. gps module with stand 7. Battery 3300 mAh 8. antivibrator 9. Brushless Motor (BR4114) Please give it a like.
Fusion 360 fusion360 telemetry raspberrypi drone

LEGO - 01 Basic Dimensions & Bricks Explained

dk
in Modeling
68 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.
Autodesk Inventor bricks dimensions lego

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

LEGO - 02 Building Bricks with Parameters

dk
in Modeling
37 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.
Autodesk Inventor parameters lego

BEVEL GEAR USING FUSION360 - LOFT

kiran
in Modeling
33 0 Beginner
here you can how to create a bevel gear using simple steps in fusion 360
Fusion 360 modelling tutorial gear bevel 360 fusion

How to model a curved spring

Jens Nielsen
in Modeling
27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA
Autodesk Inventor coil 3dintersection surface sweep spring

Inventor 2019 Crash Course for Complete Beginner

CAD Pond
in Modeling
26 6 Beginner
Still spending so much time, struggling with learning Inventor on your own? You can stop now! Get a detailed explanation of every single tool. This is the first of a series, and I'll like you to check below to know what to expect in this volume. In this Tutorial, I shall introduce briefly the Inventor 2019 interface, demonstrate how to access the inventor self-help learners path, demonstrate the way to set up the software with your desired Unit style, and then put in my best to handle every single sketch tool in detail.
Autodesk Inventor beginner sketch tutorial 2019 inventor autodesk

FreeCAD Basic Exercise #5

Quentin Plisson
in Modeling
25 0 Beginner
This tutorial allows you to discover new Additive tools in FreeCAD Part Design workbench: Additive loft and Revolution. It also introduces the notion of Datum object to create new reference elements in a part.
FreeCAD datum exercise basic revolution loft open-source additive

Complete AI Robotic Arm Design Overview

Rugved Chavan
in Modeling
24 1 Intermediate
Components used: 1) Raspberry Pi 4 extension 2) Servo motor Driver 3) High torque Servo Motors 4) Aluminium frame 360 freedom 5) Sony WebCam and Microphone Do like it..
Fusion 360 robotics fusion360 raspberrypi roboticarm

FreeCAD Basic Exercise #1

Quentin Plisson
in Modeling
25 5 Beginner
The objective of this tutorial will be to discover the workflow for the parametric design of a 3D object with Part Design and Sketcher. For this we will model a basic part involving different types of functions.
FreeCAD sketcher design part exercise basic

How to create a Square to Round (Autodesk Inventor)

David Tate
in Modeling
21 5 Beginner
This tutorial will run you through the process to create a sheet metal square to round from start to finish. Including flat pattern.
Autodesk Inventor lengthy inventor round square metal sheet

{​VIDEO}​ How to Route Electrical Cables & Twist Wires in Fusion 360

Engineering Juice
in Modeling
21 0 Beginner
How to Route Electrical Cables & Twist Wires in Fusion 360: [Please Thumbs Up!]
Fusion 360 robotics robot wire cable electrical tutorial 360 fusion

Simple Injection Mould Design - Plastic Cups Product

Muhammad Yunus
in Modeling
21 0 Intermediate
This tutorial shows you how to create a simple plastic mold design. Two Plate Mold & Single Cavity.
Autodesk Inventor plastic cups mold design plastic injection molding injection mould design

LEGO - 03 Using Data from LDraw

dk
in Modeling
20 0 Intermediate
Sometimes LEGO bricks don't fall into the regular 0.8/1.6mm rule. This will explain how to get "lumpy" 3D surface data from LDraw DAT files and use them to create your own intelligent parts. *I use the AutoDesk Inventor Pro suite, which includes Inventor Pro and 3D Studio Max. I will discuss using certain file formats, but you need to determine what your software will import/export. *I've been told that IV 2017+ will let you measure the LDraw data directly in Inventor, removing the whole 3DMax conversions steps.
Autodesk Inventor ldraw lego

Design a P-51D Mustang in Fusion 360

leo zeng
in Modeling
19 0 Beginner
Learn how to make a simple P-51 Mustang step by step.
Fusion 360 360 fusion design cad aircraft p-51 mustang
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.