Tutorials

  • Drafting ×
  • Process Simulation ×
  • Process ×
  • ArchiCAD ×
  • Autodesk Inventor ×
  • Fusion 360 ×
  • JT ×
  • Mastercam ×
  • Rhino ×
  • Other ×

Cap screws and machine screws

dea
in Drafting
65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

Create blue print by Autodesk Inventor

Ebrahim Zokaee
in Drafting
2 1 Intermediate
In this tutorial, study how to create a blue print by Autodesk inventor.
Autodesk Inventor inventor drafting blue print

Solidworks drawings tutorial

Rosandro Babosa
in Drafting
1 0 Intermediate
In this video I will be showing you how to make a professional drawing in Solidworks 2017 So I am showing you exactly these things here: 1) Make drawing from part 2) Make auxiliary view 3) Section view 4) Detail view 5) Geometric Tolerance 6) Surface Finish 7) Tolerance/Precision 8) Edit sheet Format 9) Converting the SLDDRW file to PDF file 10) Fliping Cutting line direction 11) Use the view palette
Other upright fsae drawing 2d drafting tutorial solidworks

Autodesk Fusion 360 Tutorial - How to Draw the Assembly and Its Components on the Same Sheet

Ardi Noerpamoengkas
in Drafting
0 0 Intermediate
We can draw the assembly and its components on the same drawing sheet. It is able to be applied by unchecking some component of assembly on drawing browser. We apply the balloons and the parts list table for drawing the assembly. We apply center mark, centerline, section view, and dimension for drawing the components.
Fusion 360 component drawing assembly tutorial cad 360 fusion autodesk

Learning Autodesk Fusion 360 in Arabic - 17

Auday
in Drafting
0 0 Intermediate
https://youtu.be/AmhIZsSNU4o كيفية تحويل الشكل المجسم الى رسوم مقطعية ووضع جميع الابعاد الضرورية لانتاج مخططات احترافية وعملية How to convert a 3D object into 2D drawings and cross sections with all the necessary dimensions to produce a very effective and professional drawings
Fusion 360

test

kemal dursun
in Drafting
0 11 Intermediate
test
ArchiCAD test

Animación Pulidora en Inventor Studio

CARLOS SEBASTIAN DI GIULIO
in Process Simulation
0 0 Intermediate
Pasos de como animar una Pulidora en Inventor Studio
Autodesk Inventor animacion

Autodesk Fusion 360 Tutorial - How to Set the Orthographic Projection

Ardi Noerpamoengkas
in Drafting
0 0 Intermediate
This tutorial is about how to set the orthographic projection on Autodesk Fusion 360. This feature is updated on October 28, 2018.
Fusion 360 autodesk fusion tutorial projection orthographic
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.