Tutorials

  • Assemblies ×
  • Translations ×
  • Process ×
  • CATIA ×
  • Fusion 360 ×
  • Lagoa ×
  • Powershape ×
  • Rhino ×
  • GrabCAD Print ×
  • GrabCAD Community ×
  • Wavefront OBJ ×

TURBOFAN | TURBINE IN CATIA

Avnish Kumar (अवनीश कुमार )
in Assemblies
44 12 Expert
The Rolls-Royce Trent 900 is a high bypass turbofan produced by Rolls-Royce plc to power the Airbus A380, competing with the Engine Alliance GP7000. Initially proposed for the Boeing 747-500/600X in July 1996, this first application was later abandoned but it was offered for the A3XX, launched as the A380 in December 2000.
CATIA autocad solidwork v6 v5 catia turbofan turbine

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

V6 Engine Design in Catia

Avnish Kumar (अवनीश कुमार )
in Assemblies
28 6 Expert
V6 Engine Design in Catia | Advanced Assembly | CATIA TUTORIALS Vedio Links-https://www.youtube.com/watch?v=IoZoQKwlWtA&t=5s A V6 engine is a six-cylinder piston engine where the cylinders share a common crankshaft and are arranged in a V configuration. The first V6 prototype engine was produced in 1906, however it took until 1950 for the first automotive V6 engine to reach production. In the past 20 to 30 years, the V6 layout has become the most common layout for six-cylinder automotive engines
CATIA step assmbly v6 v5 catia enigine engine automobile

Assembly Boolean in CATIA

Ananth Narayan
in Assemblies
17 2 Intermediate
When one thinks how to match thread profile of bolt to the hole to avoid minor clash, then here is the tutorial. This method can be used for other application where you don't need much work.
CATIA boolean catia

Sheet Metal Rolling Machine

Avnish Kumar (अवनीश कुमार )
in Assemblies
16 1 Expert
Sheet metal rolling machine
CATIA solidwork v6 catia

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

How to FDM Print for Part Sliding Clearance

GrabCAD Tutorials
in Assemblies
13 4 Intermediate
If you are 3D printing parts that have to fit/slide together after printing, you will need to put some sort of clearance between those parts in your CAD system. A good starting place is a clearance 2x the layer height you are going to print at, but you should make a few smaller test prints at different clearances to see if the 2x layer height rule holds for your particular situation and orientation. Have fun and happy printing!
GrabCAD Print sliding clearance printing 3d fdm

Back door design and Engineering Feature

Nishanth kumar
in Assemblies
13 4 Intermediate
This project aims to design a sheet metal panel for a car's backdoor using provided skin data while adhering to design rules and guidelines. The backdoor serves various functions, including rear coverage, visibility, and storage. The design process involves selecting the backdoor type (top-mounted, side-mounted, or bottom-mounted), choosing materials (steel or aluminum), and creating components like outer and inner panels, hinges, and reinforcements. The design is based on factors like rear visibility, sealing, structural support, crash regulations, and joining techniques. The outcome is a well-designed backdoor assembly that considers both functionality and aesthetics.
CATIA dfm car parts exterior trim catia surface design sheet meatl car back door back door

V6 ENGINE IN CATIA TUTORIALS

Avnish Kumar (अवनीश कुमार )
in Assemblies
11 5 Expert
A V6 engine is a six-cylinder piston engine where the cylinders share a common crankshaft and are arranged in a V configuration. The first V6 prototype engine was produced in 1906, however it took until 1950 for the first automotive V6 engine to reach production. In the past 20 to 30 years, the V6 layout has become the most common layout for six-cylinder automotive engines.
CATIA

Saving your Fusion 360 design in your local storage

Riolito Paildelan - GCPH
in Translations
11 0 Intermediate
Hi @https://grabcad.com/cyrhuz.sortijas.bocar-1, You've mentioned earlier that your license is about to expire. The good news is it will prompt you options of renewing your educational license. I figured that you asked about these because you're worried that your precious thesis file that you put in so much effort will be lost. Luckily all design files from f360 is saved in the cloud (internet connection required). So there's pretty much nothing to worry about. Anyhow, here's a quick tutorial on how to save your f360 design file on your local storage as a safety precaution.
Fusion 360 storage local cloud 360 fusion

Robotic Tank Tread Assembly- Fusion 360 Tutorial (Tracked Robot Part 2)

Engineering Juice
in Assemblies
10 3 Beginner
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 Buy this chain: https://amzn.to/3f2FZEl In this series, we will design and develop a tracked, tank-like mobile robot optimized for use on sand and in desert environments. The modeling of the treads, custom sprocket, idler rollers and 3D printed suspension system will be shown in great detail. We will first create the chain links themselves and the tread pieces, then pattern them along the shape of the loop. Once we finish this, we will create the custom sprocket and motor connection followed by the idler spindle and finally the suspension system. In the end, we can mirror our entire assembly to the other side to create the right side tread. Working on only one side at a time makes it easier on our computers and allows us to work faster with less lag-time.
Fusion 360 robotics tutorial 360 fusion

Pulley Tensioner 2, Fusion 360, animation

Auday
in Assemblies
9 0 Expert
another Pulley Tensioner disassembly using Fusion 360 Animation
Fusion 360

Boolean Operations & Powercopy in CATIA

DHANASEKAR VINAYAGAMOORTHY
in Assemblies
7 0 Expert
This tutorial contains explanations for Boolean operations & Powercopy in CATIA
CATIA powercopy trimming intersecting subtract add boolean

Clash Analysis In CATIA V5

Innovative Mechanical Designs
in Assemblies
6 0 Intermediate
In this video i have explained clash detection analysis in CATIA V5 assembly design workbench.
CATIA catiaclashanalysis catiaassemblydesign v5 catia

Robotic Suspension System 4- Fusion 360 Tutorial (Tracked Robot Part 9)

Engineering Juice
in Assemblies
6 0 Beginner
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 Robotic Suspension System 4- Fusion 360 Tutorial (Tracked Robot Part 9)
Fusion 360 robot robotics lesson tutorial 360 fusion
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.