Tutorials

  • Design & CAD ×
  • Other ×
  • Autodesk Inventor ×
  • Fusion 360 ×

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

Constantin STANCESCU
in Design & CAD
73 18 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw
Autodesk Inventor centrifugal_pump inventor_2014 ipt multi-body spiral coil

New approach in designing and modelling an Oil pump using Inventor 2016

Ebrahim Abu Has
in Design & CAD
107 13 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...
Autodesk Inventor ticks tips some splines parallel shafts keyways keys shaft design gears spur

Cap screws and machine screws

dea
in Drafting
65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

LEGO - 01 Basic Dimensions & Bricks Explained

dk
in Modeling
68 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.
Autodesk Inventor bricks dimensions lego

How to model a curved spring

Jens Nielsen
in Modeling
27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA
Autodesk Inventor coil 3dintersection surface sweep spring

How to model a Control lever shaft using Inventor 2014?

Constantin STANCESCU
in Design & CAD
32 8 Intermediate
If you are really interested in modeling with Inventor (2014), try to apply every step with respect to their order and watch how you reach the model. You can watch the live modeling of this part with Inventor 2021 by using this link: https://youtu.be/gOkTy_oJdH0 Enjoy!
Autodesk Inventor

How to model a dodecahedron

Jens Nielsen
in Modeling
15 8 Intermediate
Let me show you how to model a platonic surface body and use it for a weldment structure. 3D-file at: https://grabcad.com/library/dodecahedron-32
Autodesk Inventor 3dsketch polygon

How to design Complete Drone Overview

Rugved Chavan
in Modeling
83 7 Intermediate
Complete Drone design with 1. raspberry pi 4 extension 2. pixhawk 3. landing gears 4. drone frame 5. telemetry module 6. gps module with stand 7. Battery 3300 mAh 8. antivibrator 9. Brushless Motor (BR4114) Please give it a like.
Fusion 360 fusion360 telemetry raspberrypi drone

Robust Master Parts

ROTHMECH
in Modeling
1 6 Intermediate
Make robust designs using multi-body master parts.
Autodesk Inventor part master body multi

How to import the model to Fusion 360?

bot bu1ld3r
in Design & CAD
5 4 Intermediate
I have successfully imported the following files: .STEP / .stp / .ipt / .sat / .iam but neither of the two you mentioned. Upload the file from the Data Panel. After upload, it should show up as a thumbnail, right click on it & then 'open'. Parametric mode will be disabled but there's a workaround on youtube (https://youtu.be/H-N1LZufT_o). Good luck.
Fusion 360 import models fusion 360 rhino sketchup

LEGO - 02 Building Bricks with Parameters

dk
in Modeling
37 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.
Autodesk Inventor parameters lego

How to model a truncated icosahedron with Autodesk Inventor

Jens Nielsen
in Modeling
12 4 Intermediate
Mix 2D- and 3D sketches to create this platonic body.
Autodesk Inventor

Create EYE Bolt Using Inventor

Mohit
in Design & CAD
4 4 Intermediate
Create EYE Bolt Using Inventor
Autodesk Inventor mechanical parts inventor eyebolt

Cessna 182 Skylane Design-using Autodesk Fusion 360

leo zeng
in Design & CAD
9 3 Intermediate
In this video, I am going to make the Cessna 182 Skylane aircraft, I used a blueprint to trace it, I made it with solid. Not even one form!!!
Fusion 360 machine design plane cad aircraft

How to model a rope in Autodesk Inventor?

Erkan Tosun
in Design & CAD
2 3 Intermediate
marian, What about SWEEP / TWIST command? You can find it under the menu; 3D MODEL / Sweep / Sweep / Twist You can
Autodesk Inventor
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.