Tutorials

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

73 18 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw

New approach in designing and modelling an Oil pump using Inventor 2016

107 13 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...

Cap screws and machine screws

65 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.

LEGO - 01 Basic Dimensions & Bricks Explained

68 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.

How to model a curved spring

27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA

How to model a Control lever shaft using Inventor 2014?

32 8 Intermediate
If you are really interested in modeling with Inventor (2014), try to apply every step with respect to their order and watch how you reach the model. You can watch the live modeling of this part with Inventor 2021 by using this link: https://youtu.be/gOkTy_oJdH0 Enjoy!

How to model a dodecahedron

15 8 Intermediate
Let me show you how to model a platonic surface body and use it for a weldment structure. 3D-file at: https://grabcad.com/library/dodecahedron-32

Robust Master Parts

1 6 Intermediate
Make robust designs using multi-body master parts.

LEGO - 02 Building Bricks with Parameters

37 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.

How to model a truncated icosahedron with Autodesk Inventor

12 4 Intermediate
Mix 2D- and 3D sketches to create this platonic body.

Create EYE Bolt Using Inventor

4 4 Intermediate
Create EYE Bolt Using Inventor

How to model a rope in Autodesk Inventor?

2 3 Intermediate
marian, What about SWEEP / TWIST command? You can find it under the menu; 3D MODEL / Sweep / Sweep / Twist You can

How to create NPT (national pipe taper) threads using inventor

13 3 Intermediate
I have had people ask me on here how I model npt threads for some of the parts I make, so I figured I would put it out there for others to see as well. Note: if you look at the threaded models I have on this website you will see that I have clearly taken more time on some of them than others, this tutorial will teach you how to do it the right and proper way.

From GRABCAD to INVENTOR

2 3 Intermediate
Download files from GRABCAD and edit it in INVENTOR Link: https://youtu.be/UasZ2dt37AU

Globoid worm in Inventor

2 3 Intermediate
Modeling accurate Globoid worm for CNC machining