Tutorials

  • Dimensioning / Tolerancing ×
  • Simulation & CAE ×
  • Process ×
  • Standards ×
  • Alibre Design ×
  • Fusion 360 ×
  • Rendering ×
  • Wavefront OBJ ×

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

Static Simulation in Fusion 360! Bicycle Crank Arm Tutorial

Engineering Juice
in Simulation & CAE
5 0 Beginner
0:25 Simulation Start 0:56 Simplify 1:31 Materials 2:02 Constraints 2:58 DOF View 3:23 Loads 4:52 Solve In this tutorial, we will create a static simulation for our bicycle crank arm in Autodesk Fusion 360. We will simplify our assembly, to remove the fittings, then add a material, constraints and a load to the end of the arm. When we solve our assembly, we will end up with the amount of deformation. We will then run the simulation again once we core out the inside of our crank arm to see the difference in the analysis.
Fusion 360 static simulation tutorial lesson 360 fusion

Static Stress Simulation: I-Beam Bending in Fusion 360! Tutorial

Engineering Juice
in Simulation & CAE
3 0 Beginner
How to do a static stress simulation on an I-beam in Fusion.
Fusion 360 beginner 2019 sketch modeling tutorial 360 fusion fusionsimulation

Fusion 360 Thermal Simulation Tutorial- Loads and Constraints Coffee Mug Part 2

Engineering Juice
in Simulation & CAE
2 0 Beginner
#Coffee #ThermalConduction #ThermalSimulation Music is from Youtube free library. -This is a thermal load simulation.
Fusion 360 thermal simulation tutorial 360 fusion

Measurement extraction

VIVEK AKASH
in Dimensioning / Tolerancing
1 0 Beginner
Extracting the measurement's of an unknown model in Fusion 360 for reference and further implements
Fusion 360 scale units extraction inspection measurments dimensioning

Introduction to Drawings in Fusion 360 — Getting Started Basics & Training Exercise for Beginners

Engineering Juice
in Dimensioning / Tolerancing
0 0 Beginner
Introduction to Drawings in Fusion 360 — Getting Started Basics & Training Exercise for Beginners
Fusion 360 cadd tutorial beginner drawings 360 fusion

Intro to Drawings - Fusion 360 Part 2: Dimensional Tolerances, Threads & Alternate Dimensions How To

Engineering Juice
in Dimensioning / Tolerancing
0 0 Beginner
Intro to Drawings - Fusion 360 Part 2: Dimensional Tolerances, Threads & Alternate Dimensions How To
Fusion 360 basics autodesk intro drawings tutorial 360 fusion

Fusion 360 parametric

Metalworks
in Dimensioning / Tolerancing
0 0 Beginner
Changing parameters in Fusion 360
Fusion 360 prametric 360 fusion fusion 360 parameter

Autodesk Fusion 360 Tutorial - How to Use Diameter Dimension on Sketching

Ardi Noerpamoengkas
in Dimensioning / Tolerancing
0 0 Intermediate
This tutorial is about how to use "Diameter Dimension" menu on Autodesk Fusion 360 Sketching. This feature is updated on October 28, 2018.
Fusion 360 tutorial 360 fusion sketching diameter dimensioning

How to do thermal ands static simulation on cantilever and Simply Supported Beam

Harsh Priyanshu
in FEM
0 0 Beginner
Hello everyone, in this simple short video, i've shown a process of using static and thermal stress simulation using Autodesk Fusion 360 . and there are somethings in the model which i overlooked as this tutorial is meant for beginners, so i've tried to keep it very simple. so follow the video till last.
Fusion 360 stress simulation 360 fusion
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.