Tutorials

  • PTC Creo Elements ×
  • Rhino ×
  • SpaceClaim ×
  • TurboCAD ×
  • surfacing ×

Filling basic 6-sided holes in Rhino

Bobi
in Modeling
8 1 Beginner
This tutorial shows how to fill a 6-sided hole surrounded by simple planar surface transitions in Rhino.
Rhino rhino blend hole 6-sided surface surfacing nurbs transition

Video Tutorials from Rhino 3D Tutorials

Alexandre Galin
in Modeling
8 0 Beginner
A series of little tutorials made available on my Youtube channel. For more detailed Rhino 3D tutorials here's the link https://rhino-3d-classes-from-beginner-to-advanced-lev.teachable.com/
Rhino surfacing 3d rhinoceros taught self tutorials prototyping rhino3d

Filling 6-sided holes in Rhino

Bobi
in Modeling
3 0 Intermediate
This tutorial shows how to fill a 6-sided hole surrounded by complex surface transitions in Rhino.
Rhino transition nurbs surfacing surface 6-sided hole blend rhino

Filling basic 6-sided holes in Rhino (ver. 2)

Bobi
in Modeling
1 0 Intermediate
This tutorial shows how to fill a 6-sided hole surrounded by simple planar surface transitions in Rhino.
Rhino transition nurbs surfacing surface 6-sided hole blend rhino

Blend surface - Advanced Planar sections (tutorial 1)

Bobi
in Modeling
1 0 Beginner
Blend surface with advanced "Planar sections" option
Rhino section planar transition nurbs surfacing surface blend rhino

Filling basic 6-sided holes in Rhino (ver. 3)

Bobi
in Modeling
1 0 Beginner
This tutorial shows how to fill a 6-sided hole surrounded by simple planar surface transitions in Rhino.
Rhino rhino blend hole 6-sided surface surfacing nurbs transition

Loft to simulate a full round fillet between 3 surfaces

Bobi
in Modeling
1 0 Beginner
In cases where 3 surfaces meet together and the goal is to create a full round fillet in-between, the top surface could be used to extract an isocurve that’s then used as a middle profile for a “Loft surface”. The two main vertical surfaces are shortened by the amount of approximate radius (in this example, the radius is 5 mm, because the two main surfaces are 10 mm far from each other) and set to tangent start and end for the loft operation. That would maintain the desired top limit for the rounded surface, though it will not produce a true radius fillet.
Rhino rhino radius surface surfacing nurbs transition round fillet

Blend surface - Advanced Planar sections (tutorial 2)

Bobi
in Modeling
1 0 Beginner
Blend surface with advanced "Planar sections" option
Rhino rhino blend surface surfacing nurbs transition planar section

Editable tween curve on surface or polysurface

Bobi
in Modeling
1 0 Beginner
History in Rhino 7 must be turned on, in order for the modifications on the input surfaces to affect the output tween surface and its corresponding curve intersection. The latter could be further simplified via the "! _RemoveMultiKnot" command, though that will destroy the history and also may cause the curve to no longer sit perfectly accurate on the surface/polysurface.
Rhino curve edit transition nurbs surfacing surface tween rhino

Super ring tutorial

Bobi
in Modeling
1 0 Beginner
Modeling tutorial for creating a ring in Rhino 7 with a single, history-enabled editable lofted surface.
Rhino gold ring loft tutorial nurbs surfacing jewerly tip

How to create a ring in Rhino

Bobi
in Modeling
0 0 Intermediate
Modeling tutorial for creating a ring in Rhino 7.
Rhino tip jewerly surfacing nurbs tutorial rhino modeling ring

Advanced surface modeling in Rhino 7

Bobi
in Modeling
0 0 Intermediate
Advanced surface modeling in Rhino 7 https://youtu.be/JDOnR5jLGbo
Rhino supercar super car vehicle automotive design nurbs surfacing

Full round fillet between 3 surfaces

Bobi
in Modeling
0 0 Beginner
This tutorial shows how to use a tangent circle to 3 surfaces to build a full round fillet in-between.
Rhino rhino radius surface surfacing nurbs transition round fillet

Modeling of an inlet lip in Rhino 7

Bobi
in Modeling
1 0 Intermediate
P.S. At the end of my video you will notice that I forgot to improve the flow at the tip between the two split surfaces (easily seen on the curvature graph), which I did after I stopped with the video recording.
Rhino blend lip inlet air intake airplane wing surfacing rhino
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.