Tutorials

  • robotics ×

I Built a Military Robot

Engineering Juice
in Process
43 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

Complete AI Robotic Arm Design Overview

Rugved Chavan
in Modeling
24 1 Intermediate
Components used: 1) Raspberry Pi 4 extension 2) Servo motor Driver 3) High torque Servo Motors 4) Aluminium frame 360 freedom 5) Sony WebCam and Microphone Do like it..
Fusion 360 robotics fusion360 raspberrypi roboticarm

{​VIDEO}​ How to Route Electrical Cables & Twist Wires in Fusion 360

Engineering Juice
in Modeling
21 0 Beginner
How to Route Electrical Cables & Twist Wires in Fusion 360: [Please Thumbs Up!]
Fusion 360 robotics robot wire cable electrical tutorial 360 fusion

Robotic Tank Tread Assembly- Fusion 360 Tutorial (Tracked Robot Part 2)

Engineering Juice
in Assemblies
10 3 Beginner
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 Buy this chain: https://amzn.to/3f2FZEl In this series, we will design and develop a tracked, tank-like mobile robot optimized for use on sand and in desert environments. The modeling of the treads, custom sprocket, idler rollers and 3D printed suspension system will be shown in great detail. We will first create the chain links themselves and the tread pieces, then pattern them along the shape of the loop. Once we finish this, we will create the custom sprocket and motor connection followed by the idler spindle and finally the suspension system. In the end, we can mirror our entire assembly to the other side to create the right side tread. Working on only one side at a time makes it easier on our computers and allows us to work faster with less lag-time.
Fusion 360 robotics tutorial 360 fusion

How to design Complete Robot using Voice Assistant like JARVIS in Fusion 360

Rugved Chavan
in Process
14 1 Intermediate
4-wheeled Robot Design Frame is 3D printable. Components - 1. Raspberry pi 4 2. Sony WebCam 3. Normal 3.5 mm jack Speaker 4. Custom Frame 5. MI 20000 mAh powerbank 6. 100 RPM Dual Shaft BO Motor - Straight with wheels Custom Voice Assistance code is running in background. Voice assistance code is connected with database which is having values like quantity and dimensions of components. Mail me for Jarvis source code. Like this video... 🤘
Fusion 360 automation electronics robots arduino engineering technology robot robotics

ROBOTIC ARM COMPLETE DESIGN

MANIKANTHA P
in Modeling
6 0 Intermediate
ROBOTIC ARM COMPLETE DESIGN
NX Unigraphics assembly assemblies robot robotic arm robotics

ROBOTIC ARM DESIGN

MANIKANTHA P
in Modeling
4 0 Beginner
A robotic arm is a type of mechanical arm, usually programmable, with similar functions to a human arm; the arm may be the sum total of the mechanism or may be part of a more complex robot. The links of such a manipulator are connected by joints allowing either rotational motion (such as in an articulated robot) or translational (linear) displacement.[1][2] The links of the manipulator can be considered to form a kinematic chain. The terminus of the kinematic chain of the manipulator is called the end effector and it is analogous to the human hand. However, the term "robotic hand" as a synonym of the robotic arm is often proscribed.
NX Unigraphics arm robot robotics unigraphics

How to Model a Suspension System- Fusion 360 Tutorial (Tracked Robot Part 6)

Engineering Juice
in Modeling
3 0 Intermediate
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 In this series, we will design and develop a tracked, tank-like mobile robot optimized for use on sand and in desert environments. The modeling of the treads, custom sprocket, idler rollers and 3D printed suspension system will be shown in great detail. We will first create the chain links themselves and the tread pieces, then pattern them along the shape of the loop. Once we finish this, we will create the custom sprocket and motor connection followed by the idler spindle and finally the suspension system. In the end, we can mirror our entire assembly to the other side to create the right side tread. Working on only one side at a time makes it easier on our computers and allows us to work faster with less lag-time.
Fusion 360 autodesk robot robotics tutorial 360 fusion

5 Jaw Robotic Gripper

Raian Nur Islam
in Modeling
3 0 Beginner
The steps are very easy to follow. The model contains 15 parts. The video lessons will show how to create each one of them using solidworks. And after that the assembly of those parts. The model can be downloaded from the link below https://grabcad.com/library/5-jaw-robotic-gripper-1 The tutorial playlist is also available on youtube https://www.youtube.com/playlist?list=PL8YLj7XoSQIeIUwe12QvUHMKKLJUL9Chf
SOLIDWORKS robotics gripper modeling solidworks 5claw jaw claw robotic

Robotic Suspension System 4- Fusion 360 Tutorial (Tracked Robot Part 9)

Engineering Juice
in Assemblies
6 0 Beginner
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 Robotic Suspension System 4- Fusion 360 Tutorial (Tracked Robot Part 9)
Fusion 360 robot robotics lesson tutorial 360 fusion

How to Build a Military Robot

Engineering Juice
in Modeling
11 0 Intermediate
https://www.youtube.com/watch?v=5bgXjKqfwAk
Fusion 360 rollerchain raspberrypicamera led dcmotor raspberrypi robotics robot fusion360

Industrial Robot Assembly Tutorial || NX Tutorials

Aakash Kumar
in Assemblies
3 0 Intermediate
This is the final tutorial of industrial robot assembly. There are total 8 parts in this assembly and In this tutorial i am going to assemble all these 8 parts to create the Industrial Robot. I am going to use different tools and techniques of NX CAD software to create this part.
NX Unigraphics tutorials assembly unigraphics nx robotics robot industrial

How to Make a DC Motor & Sprocket Assembly: Fusion 360 Robotics Tutorial for Beginners (Robot Part 3)

Engineering Juice
in Assemblies
2 0 Beginner
#Fusion360 #Fusion360Tutorial #AutodeskFusion360 In this series, we will design and develop a tracked, tank-like mobile robot optimized for use on sand and in desert environments. The modeling of the treads, custom sprocket, idler rollers and 3D printed suspension system will be shown in great detail. We will first create the chain links themselves and the tread pieces, then pattern them along the shape of the loop. Once we finish this, we will create the custom sprocket and motor connection followed by the idler spindle and finally the suspension system. In the end, we can mirror our entire assembly to the other side to create the right side tread. Working on only one side at a time makes it easier on our computers and allows us to work faster with less lag-time. Buy this chain for projects: https://amzn.to/3f2FZEl
Fusion 360 project robotics assemblies beginner tutorial 360 fusion

6 Axis Robotic Arm in CATIA V5 Tutorial | DMU Kinematics | Assembly

Vishal Bharat Patil
in Kinematics
3 0 Intermediate
In this tutorial, I have designed and simulate the 6 Axis Robotic Arm. Also, one can learn the simulation in CATIA V5 with precise commands and instructions to perform the operations. I'm very happy to get so much response from your YouTube family, Hoping for a Positive and vibrant response to this video. Please share and comment below doubts as well as feedbacks Or Mail me your query at vishalbharatpatil5@gmail.com
design robotics tutorial v5 catia arm robotic axis

how to design the robot in Catia|| 6-axis robot

auto design solutions
in Modeling
2 0 Intermediate
in this tutorial, I show the how-to design the 6-axis robot in CATIA software. if you like do subscribe
CATIA animation robotics catia robot
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.