Tutorials

NX 11:Creating Assembly

14 2 Beginner
A tutorial on Sub assembly and showing arrangements of hydraulic cylinder-piston assembly.

How to Convert CAD Files to STL Files in Various Software

10 8 Beginner
How CAD files are exported to STL is an important process for the accurate building of parts, but the conversion process can vary depending on the software. These step-by-step processes for converting CAD files to STL were taken straight from the mentioned companies websites.

(VIDEO TUTORIAL) MECHANICAL BIRD Design in UNIGRAPHICS | Flapping wing mechanism design

10 0 Expert
When a bird flaps, as opposed to gliding, its wings continue to develop lift as before, but the lift is rotated forward to provide thrust, which counteracts drag and increases its speed, which has the effect of also increasing lift to counteract its weight, allowing it to maintain height or to climb

Car design in NX

9 1 Beginner
Car design in nx

Roller bracket in NX

9 2 Beginner
Modeling and assembly

Radial engine Animation in NX

9 4 Intermediate
Applications. Radial engines have several advantages for airplanes: They can produce a lot of power. A typical radial engine in a B-17 has nine cylinders, displaces 1,800 cubic inches (29.5 liters) and produces 1,200 horsepower.

Drone Design in NX

7 2 Beginner
An unmanned aerial vehicle (UAV) (or uncrewed aerial vehicle,[2] [3]commonly known as a drone) is an aircraft without a human pilot on board and a type of unmanned vehicle. UAVs are a component of an unmanned aircraft system (UAS); which include a UAV, a ground-based controller, and a system of communications between the two. The flight of UAVs may operate with various degrees of autonomy: either under remote control by a human operator, autonomously by onboard computers [4] or piloted by an autonomous robot.[5]

Mountain bike design in SIEMENS NX

7 0 Intermediate
A mountain bike (MTB[1]) or mountain bicycle is a bicycle designed for off-road cycling. Mountain bikes share some similarities with other bicycles, but incorporate features designed to enhance durability and performance in rough terrain. These typically include a suspension fork, large knobby tires, more durable wheels, more powerful brakes, straight handlebars, lower gear-ratios for climbing steep grades and sometimes rear suspension to really smooth out the trail

DRONE ASSEMBLY DESIGN in SIEMENS NX

7 0 Beginner
Drone assembly design using Siemens NX, An unmanned aerial vehicle (UAV) (or uncrewed aerial vehicle,[2] commonly known as a drone) is an aircraft without a human pilot on board. UAVs are a component of an unmanned aircraft system (UAS); which include a UAV, a ground-based controller, and a system of communications between the two.[3] The flight of UAVs may operate with various degrees of autonomy: either under remote control by a human operator or autonomously by onboard computers[4] referred to as an autopilot.

Beginner CAD Tutorial for Any Software

4 0 Beginner
For those who are beginner and looking for practice video which helps in interpreting CAD drawings for 3d modeling creation and applying better modeling practices, here is the video link of tutorials. This tutorial is "IRRESPECTIVE OF ANY CAD SOFTWARE". So anyone can follow it very easily. There are 20 videos and many more to come.

EARTH MOVERS VEHICLE DESIGN

4 0 Beginner
Earth Movers playlist: https://www.youtube.com/playlist?list=PLsTi7aWegx-Aj1yoQz-qFYag1v85y96vv

Scissor Lift Animation in SIEMENS NX

4 0 Beginner
This mechanism is used in devices such as lift tables and scissor lifts. Modern low-profile computer keyboards make an extensive use of it as well, installing each key on a scissor support to ensure their smooth vertical movement, allowing the use of a cheap and reliable rubber dome contact set, instead of expensive and complex array of mechanical switches.

ROBOTIC ARM DESIGN

4 0 Beginner
A robotic arm is a type of mechanical arm, usually programmable, with similar functions to a human arm; the arm may be the sum total of the mechanism or may be part of a more complex robot. The links of such a manipulator are connected by joints allowing either rotational motion (such as in an articulated robot) or translational (linear) displacement.[1][2] The links of the manipulator can be considered to form a kinematic chain. The terminus of the kinematic chain of the manipulator is called the end effector and it is analogous to the human hand. However, the term "robotic hand" as a synonym of the robotic arm is often proscribed.

Industrial Robot Assembly Tutorial || NX Tutorials

3 0 Intermediate
This is the final tutorial of industrial robot assembly. There are total 8 parts in this assembly and In this tutorial i am going to assemble all these 8 parts to create the Industrial Robot. I am going to use different tools and techniques of NX CAD software to create this part.

NX 11 Unigraphics tutorial

3 0 Beginner
Hello New video tutorial for beginners, to make this part I used command extrude and revolve. If you start learn NX it's perfect part for you. Thank you for your attention, subscribe and like it's motivated me